IDOLA06 Solid Hand (Angled Finger/XS)

4595120205115

B0F4QBYK3S

Idola Solid Hand - 1/144 Scale - Plastic Model Parts Product Introduction Idola "Solid Hand Square Finger XS Size 1/144 Scale" is a plastic model part. Solid Hands are 3D-printed detail-enhancing parts. For humanoid character robots, the size and shape of the fist have a significant impact on the overall impression of the model, making them a key point of emphasis for character robot modelers. Currently, there are many aftermarket hand parts available on the market to replace kit parts, but they contain too much detail and can sometimes look out of place when attached to the kit. Most of these are designed for robots with heights in the 18-20m class, which can create unnatural proportions when used on smaller robots. Therefore, we have created a lineup of three sizes compatible with 1/144 scale, featuring simple designs with minimal molded detail to blend in with a variety of robot character models. If you install the fist parts included with the kit, which are oversized for the overall balance due to molding reasons or parts with holes in the fists to hold weapons, without any modification, the overall proportions may be disrupted or the realism may be lost. These parts can be used to further improve the appearance. Even the extremely small molds that are difficult to process by hand are reproduced with the precise detail that only a 3D printer can achieve. At the same time, the simple design ensures compatibility with many character robot kits. The size is designed for use with 1/144 character robot kits. The set includes two pairs of gripping hands (left and right), one pair of flat hands (left and right), and separate parts for the back of the hand, so one set can be used with multiple kits. The gripping fist parts precisely recreate the shape of a tightly clenched thumb, similar to the human form. The flat hand parts are sculpted to create a natural, relaxed line.
If the fist is the right shape and size, the arm will appear shorter, and if the arm appears shorter, the legs will appear longer, resulting in a slimmer, more sleek figure with a taller body.
Even if you're thinking of building a straight fist, adding just the fist parts will make it look cool and tighten the overall image.
Each size is intended for use with 1/144 scale character robot kits.
XS size: 15m class (kit height: 115mm and up)
S size: 18m class (kit height: 125mm and up)
M size: 20m class (kit height: 140mm and up)
The basic form of each size is the same, but to prevent mistakes during storage or assembly,
there are two designs (XS and M are simple designs, while S is a complex design with many details).
The parts can be processed in the same way as plastic models.
Cut the support material (strut) under the fist with thin-bladed nippers and shape it flat with a file. Support material is only found near the wrist, so there's no need to worry about losing the fine details. To remove layer marks and dots typical of SLA, sand the surface with #320 waterproof sandpaper. Then, sand with #400-600 for a clean finish. If the ball joint is tight, you can sand it down with sandpaper. If it's loose, you can apply instant glue or other adhesive to adjust. This model can also be painted just like a plastic kit. To improve paint adhesion, we recommend lightly cleaning the parts with a mild detergent and then spraying on a primer. The upper arm is a separate part, making it easy to paint different parts. Painting the joints in different colors enhances the sense of precision. Metallic colors also add a nice accent. This product, previously sold as a "Mechanical Hand," has been significantly redesigned using the latest 3D printer technology. The robot kit is not included. This product is a plastic model kit part. Plastic model kit not included. *Separate adhesives, tools, paints, etc. are required for assembly. *"Plastic Model" is a registered trademark of the Japan Plastic Model Industrial Cooperative. *This product does not include adhesives, paints, tools, batteries, etc. Safety Warning: Not applicable. Brand: Idola. Unisex. Material: Resin. Plastic model kit not included. Plastic model parts require assembly and painting. Separate adhesives, tools, paints, etc. are required. 1/144 scale detail-up parts. XS size: For a 15m-class figure (kit height: 115mm and above). 3D printed. Set includes: Gripping hands (2 pairs, left and right), flat hands (1 pair, left and right), and backs of hands x 6. 4595120205115 IDOLA06 Idola Solid Hands (Square Fingers, XS) (text created at , 2025-08-11)

54x29x101 mm

10 g