Sanwa Supply PoE Extender Waterproof (IP67) 2-Port Output Up to 100m Extension Operating Temperature -20°C to 60°C Compatible LAN-EXPOE3
JAN
4969887758182
ASIN
B0CM8G2Z22
Maker
Model No.
LAN-EXPOE3
Color
Size
Description
Sanwa Supply LAN EXPOE3 PoE Extender (Waterproof, 2-Port Output)
▪️This PoE extender supports IEEE 802.3bt (90W)/at (30W)/af (15.4W) PoE reception. It can extend power and communication to two PoE devices (IEEE 802.3at/af) up to 100m.\
*Theoretical value.\
▪️By receiving IEEE802.3bt (90W) PoE power, this unit can split the power into two outputs to supply IEEE802.3at (30W) and af (15.4W) PoE power.\
▪️This industrial PoE extender meets the IP67 waterproof standard, enabling PoE signal transmission and extension outdoors.\
▪️Operates within a temperature range of -20°C to 60°C, functioning reliably in diverse environments.\
▪️The unit itself operates on PoE power, eliminating the need for power cables during relaying/extension.\
▪️By relaying up to two units, LAN cables can be extended up to approximately 300m. Additionally, the split LAN signal can be further distributed to power and communicate with multiple PoE devices.\
▪️Equipped with LEDs to indicate communication and power supply status. 【Important Notes】\
*This is a theoretical value based on LAN cable specifications.\
*Power loss along the LAN cable and power consumption by the unit itself will reduce the PoE power supplied when passing through this product.\
*The maximum number of devices that can be extended may vary depending on the specifications of the PoE-supplying equipment and the cable length, as the supplied power differs accordingly. \
※The PoE-supplying device must support IEEE 802.3af/at/bt, and the powered PoE device must support IEEE 802.3at/af.\
※If the PoE-supplying device is IEEE 802.3af, PoE power output from this product is not supported. (Power will be supplied, but voltage and power output will not comply with PoE standards.)\
※Use Category 5e/6/6a straight LAN cables with a gauge of 24AWG or larger for PoE power delivery. Using cables thinner than 24AWG may compromise waterproof performance.\
※Use LAN cables with a connector diameter of 13mm or smaller. If the LAN connector is larger than 13mm, it will not fit through the waterproof cap.\
※If the LAN connector has a latch cover, cut it off before use.\
Recommended Cables (Sanwa Supply)\
KB-T6AAD Series (23AWG) ※Requires removal of the clip-break prevention cover\
KB-T6POE Series (22AWG) ※Requires removal of the latch cover\
KB-T6TS Series (23AWG)\
KB-T5T Series (24AWG), etc.\
※This product's PoE OUT supports only IEEE802.3af/at. Therefore, IEEE802.3bt PoE devices will not function when connected.\
※The waterproof function is only active when LAN cables are connected to all PoE input/output ports of this product. Please note that it is not waterproof when LAN cables are not connected.\
■Color: Silver\
■Size: W150 × D72.94 × H43.8mm\
■Weight: Approx. 372g\
■Number of Ports: 2 ports\
■Maximum Transmission Speed: 1000Mbps (1000BASE-T)\
■Standards: IEEE802.3 (10BASE-T)\
IEEE802.3u (100BASE-T)
▪️This PoE extender supports IEEE 802.3bt (90W)/at (30W)/af (15.4W) PoE reception. It can extend power and communication to two PoE devices (IEEE 802.3at/af) up to 100m.\
*Theoretical value.\
▪️By receiving IEEE802.3bt (90W) PoE power, this unit can split the power into two outputs to supply IEEE802.3at (30W) and af (15.4W) PoE power.\
▪️This industrial PoE extender meets the IP67 waterproof standard, enabling PoE signal transmission and extension outdoors.\
▪️Operates within a temperature range of -20°C to 60°C, functioning reliably in diverse environments.\
▪️The unit itself operates on PoE power, eliminating the need for power cables during relaying/extension.\
▪️By relaying up to two units, LAN cables can be extended up to approximately 300m. Additionally, the split LAN signal can be further distributed to power and communicate with multiple PoE devices.\
▪️Equipped with LEDs to indicate communication and power supply status. 【Important Notes】\
*This is a theoretical value based on LAN cable specifications.\
*Power loss along the LAN cable and power consumption by the unit itself will reduce the PoE power supplied when passing through this product.\
*The maximum number of devices that can be extended may vary depending on the specifications of the PoE-supplying equipment and the cable length, as the supplied power differs accordingly. \
※The PoE-supplying device must support IEEE 802.3af/at/bt, and the powered PoE device must support IEEE 802.3at/af.\
※If the PoE-supplying device is IEEE 802.3af, PoE power output from this product is not supported. (Power will be supplied, but voltage and power output will not comply with PoE standards.)\
※Use Category 5e/6/6a straight LAN cables with a gauge of 24AWG or larger for PoE power delivery. Using cables thinner than 24AWG may compromise waterproof performance.\
※Use LAN cables with a connector diameter of 13mm or smaller. If the LAN connector is larger than 13mm, it will not fit through the waterproof cap.\
※If the LAN connector has a latch cover, cut it off before use.\
Recommended Cables (Sanwa Supply)\
KB-T6AAD Series (23AWG) ※Requires removal of the clip-break prevention cover\
KB-T6POE Series (22AWG) ※Requires removal of the latch cover\
KB-T6TS Series (23AWG)\
KB-T5T Series (24AWG), etc.\
※This product's PoE OUT supports only IEEE802.3af/at. Therefore, IEEE802.3bt PoE devices will not function when connected.\
※The waterproof function is only active when LAN cables are connected to all PoE input/output ports of this product. Please note that it is not waterproof when LAN cables are not connected.\
■Color: Silver\
■Size: W150 × D72.94 × H43.8mm\
■Weight: Approx. 372g\
■Number of Ports: 2 ports\
■Maximum Transmission Speed: 1000Mbps (1000BASE-T)\
■Standards: IEEE802.3 (10BASE-T)\
IEEE802.3u (100BASE-T)
Package
Size (Approx.):
Size (Approx.):
188x87x244 mm
Package
Weight (Approx.):
Weight (Approx.):
650 g
24,634 JPY (Including Tax)
Stock :
5
Scheduled Shipping:
2026-05-20
Quantity :
Reference Price from Other Stores
